A microbial fuel cell (MFC), which is a new type of energy source, utilises electrogenic bacteria in sewage or soil to convert chemical energy into electrical energy. MFCs typically require an external controller to provide a stable output voltage to the external load. This study develops a non-fragile guaranteed cost (NFGC) controller to suppress the interference of the controller of an MFC and ensure that the quadratic cost function of the system satisfies certain performance indexes. First, for the convenience of controller design, a Takagi-Sugeno fuzzy model is established to approximate a single-chamber single-population MFC model. Subsequently, the linear matrix inequality method is used to design the NFGC controller. This control scheme can reduce the influence of controller disturbances on the system and ensure asymptotic stability of the closed-loop system under the specified upper bound of the provided cost function. The simulation results demonstrate that the developed control method has a shorter adjustment time and smaller steady-state error than traditional control methods such as sliding mode control (SMC), backstepping control, and fuzzy SMC.
Bioelectric Energy Sources , Fuzzy Logic , Computer Simulation , Algorithms , Electricity
Transition metal-catalyzed divergent synthesis through alternation of the catalyst is appealing, as it provides an operationally simple way to access different valuable products, while using the same reactants as starting materials. Herein, a gold-catalyzed cascade reaction of conjugated diynamides with allylic alcohols is described. By variation of the catalysts, substituted allenes and furans could be obtained selectively. Mechanistic studies indicate that, after the addition of allylic alcohol to gold-activated diynamide, a [3,3]-sigmatropic rearrangement would take place and lead to the formation of a common reactive intermediate, which would further convert to the final products selectively. Further variation of the structure of diynamides has unveiled an additional reaction sequence involving intramolecular Himbert arene/allene Diels-Alder cycloaddition to afford a series of dearomatized products bearing bicyclo[2,2,2]octadiene core.
Gold , Propanols , Gold/chemistry , Catalysis
Nano-silica (NS) is an effective material to improve the strength and durability of high-performance concrete (HPC), but little information is available regarding its role in HPC response to long-term sulfate attack. In this study, six different dosages of NS (0%, 1%, 2%, 3%, 4%, and 5%) as cement partial replacement were mixed into HPC and the casted specimens were soaked in sulfate solution for different periods (0, 100, 200, and 300 days). The mass change, dynamic elastic modulus, compressive and splitting strength, microstructure morphology, and porosity characteristics of HPC specimens were measured by mass tests, mechanical properties tests, scanning electron microscopy (SEM), and nuclear magnetic resonance (NMR) tests. The results showed that the incorporation of NS decreased the mass loss, elevated the compressive and splitting strength, and reduced the porosity formation of HPC in front of sulfate attack. The percentage of 1% NS was among the most effective dosages as, after soaking for 300 days, it decreased the mass loss by 13.5%, elevated the elastic modulus as well as compressive and splitting strength by 50.4%, 31.7%, and 69.8% in comparison of unmodified HPC, respectively. The sulfate attack resistance was delayed in a higher (2-5%) mixed dosage, mainly due to the agglomeration of nano particles, especially after long-term reactions. This study can provide experimental references regarding the performance of HPC mixed with NS in front of sulfate attack.
In recent years, recycled aggregate concrete (RAC) has become a research hotspot in the field of urban construction because of its resource utilization of construction waste. However, compared with original concrete, its strength is still low, which requires additional nano-SiO2 (NS) and fiber. In order to study the mechanism of strength improvement of RAC, this paper takes NS and polyvinyl alcohol (PVA) fiber as variable parameters; uniaxial and triaxial compression tests were carried out on RAC with PVA fiber and NS, and the mechanical properties of RAC were investigated The result shows that within the range of 3% NS content, an increase in the NS substitution rate causes the mechanical properties of RAC to improve significantly. The compressive strength of RAC increases again after adding PVA fiber; through a SEM (scanning electron microscopy) analysis of the specimen, it was found that the NS filled the micro-pores and micro-cracks in the RAC, and the PVA fiber changed the contact range between recycled aggregate and mortar, so the microstructure of the material was more compact. The mechanism of RAC strength improvement is explained in the microcosmic view.
According to the basic principle of dense packing of particles, and considering the interaction between particles, a dense packing model of granular materials in concrete was proposed. During the establishment of this model, binary particle packing tests of crushed stone and sand were carried out. The fitting analysis of the test results determines the relationship between the particle size ratio and the remaining volume fraction of the particle packing, and then the actual void fraction of the particle packing was obtained, based on which the water-binder ratio was combined to determine the amount of various materials in the concrete. The proposed concrete mix design method was used to prepare concrete, and its compressive strength and elastic modulus were tested experimentally. The test results show that the aggregate volume fraction of the prepared concrete increased, and the workability of the concrete mixture with the appropriate amount of water reducing agent meets the design requirements. When the water-binder ratio was 0.42, 0.47, or 0.52, the compressive strength of the concrete increased compared with the control concrete, and the degree of improvement in compressive strength increased with the decrease in water-binder ratio; when the water-binder ratio was 0.42, 0.47, or 0.52, the static elastic modulus of the concrete increased compared with the control concrete, and the degree of improvement in elastic modulus also increased with the decrease in water-binder ratio. The elastic modulus and compressive strength of the prepared concrete have a positive correlation. Findings show that the concrete mix design method proposed by this research is feasible and advanced in a sense.
Glioma is the most common type of primary brain cancer, and the prognosis of most patients with glioma, and particularly that of patients with glioblastoma, is poor. Tumor immunity serves an important role in the development of glioma. However, immunotherapy for glioma has not been completely successful, and thus, comprehensive examination of the immune-related genes (IRGs) of glioma is required. In the present study, differentially expressed genes (DEGs) and differentially expressed IRGs (DEIRGs) were identified using the edgeR package. Kyoto Encyclopedia of Genes and Genomes (KEGG) pathway analysis was used for functional enrichment analysis of DEIRGs. Survival-associated IRGs were selected via univariate Cox regression analysis. A The Cancer Genome Atlas prognostic model and GSE43378 validation model were established using lasso-penalized Cox regression analysis. Based on the median risk score value, patients were divided into high-risk and low-risk groups for clinical analysis. Receiver operating characteristic curve and nomogram analyses were used to assess the accuracy of the models. Reverse transcription-quantitative PCR was performed to measure the expression levels of relevant genes, such as cyclin-dependent kinase 4 (CDK4), interleukin 24 (IL24), NADPH oxidase 4 (NOX4), bone morphogenetic protein 2 (BMP2) and baculoviral IAP repeat containing 5 (BIRC5). A total of 3,238 DEGs, including 1,950 upregulated and 1,288 downregulated DEGs, and 97 DEIRGs, including 60 upregulated and 37 downregulated DEIRGs, were identified. 'Neuroactive ligand-receptor interaction' and 'Cytokine-cytokine receptor interaction' were the most significantly enriched pathways according to KEGG pathway analysis. A prognostic model and a validation prognostic model were created for glioma, including 15 survival-associated IRGs (FCER1G, NOX4, TRIM5, SOCS1, APOBEC3C, BIRC5, VIM, TNC, BMP2, CMTM3, IL24, JAG1, CALCRL, HNF4G and CDK4). Furthermore, multivariate Cox regression analysis results suggested that age, high WHO Grade by histopathology, wild type isocitrate dehydrogenase 1 and high risk score were independently associated with poor overall survival. The infiltration of B cells, CD8+ T cells, dendritic cells, macrophages and neutrophils was positively associated with the prognostic risk score. In the present study, several clinically significant survival-associated IRGs were identified, and a prognosis evaluation model of glioma was established.
The pyrite oxidation is crucial to the overall black shale oxidation process. A. ferrooxidans was documented an effective oxidation ability on pure pyrite, but its role in black shale oxidation is unclear. In this study, a comparative study of acid solution and A. ferrooxidans on the micro-surface characteristics at the initial stage (7 days) was conducted on black shale slices, a comprehensive approach combining the micro-morphologies, micro-structures, micro-environmental pH and micro-surface elemental content were investigated by using polarizing microscopies, SEM, fluorescent staining and EDX line scan analysis. The pyrite oxidation rate was employed to the index for black shale oxidation degree, and analyzed by XRD, aqueous pH, oxidation-reduction potential (ORP), ferrous and ferric ions concentrations measurement. The results show that the micro-surface characteristics are different in acid solution and A. ferrooxidans groups, which significantly impact the pyrite oxidation rate. A. ferrooxidans promote the jarosite formation and elemental C accumulation on the rocks micro-surface, which is assumed to inhibit further reactions. Two reaction phases named "pyrite oxidized phase" and "jarosite formation phase" are proposed to occur in the initial stage of A. ferrooxidans oxidizing black shale. These findings provide experimental data to evaluate the micro-surface reactions during black shale oxidation process.
This paper addresses the problems of robust stability analysis and L1-gain controller synthesis for uncertain impulsive positive systems. First, by employing the idea of impulse interval partitioning, an impulse-time-dependent discretized copositive Lyapunov function is proposed to analyze the robust stability and L1-gain performance of the considered system without control inputs, and several stability conditions and L1-gain criteria are respectively derived. Subsequently, a sufficient condition is formulated for the existence of state-feedback controllers with which not only the positivity and robust uniform asymptotic stability of the resulting closed-loop system are guaranteed, but also a prescribed L1-gain performance is satisfied simultaneously. Furthermore, to make the controller synthesis problem numerically tractable, we propose an iterative convex optimization algorithm to compute the desired controller parameters. Finally, three numerical examples and two realistic examples are presented to show the effectiveness and applicability of the proposed methodology.
An understanding of the processes that control the behavior of major elements with respect to weathering profile is essential to calculate the mobility, redistribution, and mass fluxes of elements. Hence, this study aims to determine the geochemical mass balance, strain, elemental correlation, and transport in weathering profiles. We constructed three weathering profiles for the black shale of Shujingtuo formation. As per the principal component analysis of major elements, density, and pH values, the first component represents the "elemental factor" and the second denotes the "external factor." The "depletion" pattern is a mass transportation pattern, and Na, K, and Mg are depleted along transect relative to the composition of fresh rock. Fe is redeposited at the bottom half of the saprock zone, whereas Al is accumulated at the regolith zone. The Fe and Al patterns are attributed to the "depletion-addition" and "addition" patterns, respectively. The strain in profiles A and B demonstrates the expansion at the regolith zone and part of the saprock zone. In profile C, however, these zones collapsed at all depths. In chemical weathering, Na, K, Ca, Mg, and Si are depleted in the following order: valley (C) > near mountaintop (B) > ridge (A).
Geologic Sediments/chemistry , Geology , Aluminum/analysis , China , Hydrogen-Ion Concentration , Iron/analysis , Magnesium/analysis , Potassium/analysis , Principal Component Analysis , Sodium/analysis , Spectrometry, X-Ray Emission , Water Movements , X-Ray Diffraction
Circulating total free fatty acid (FFA) levels are elevated early in myocardial infarction (MI) and have been associated with an increase in mortality. We investigated the association of serum unbound FFA (FFAu) levels with mortality in patients presenting with ST-segment elevation MI in the Thrombolysis In Myocardial Infarction II trial. The Thrombolysis In Myocardial Infarction II trial enrolled patients within 4 hours of chest pain onset. The patients were treated with a recombinant tissue plasminogen activator within 1 hour of enrollment. The FFAu concentration was evaluated in serum samples from 1,834 patients obtained at baseline, before therapy. The FFAu level was an independent risk factor for death as early as at 1 day of hospitalization and continued to be an independent risk factor for the >3.8 years of follow-up. When adjusted for other cardiovascular risk factors, the FFAu levels in the fourth versus the first quartile remained an independent risk factor for death from MI (hazard ratio 5.0, 95% confidence interval 1.9 to 13.0), all cardiac death (hazard ratio 2.4, 95% confidence interval 1.3 to 4.4), and all-cause death (hazard ratio 1.9, 95% confidence interval 1.2 to 3.1). Women were twice as likely to be in the upper 2 FFAu quartiles and had approximately twice the rate of death as men. In conclusion, FFAu elevation is 1 of the earliest molecular biomarkers of mortality in patients with ST-segment elevation MI and was independent of other risk factors known to affect the outcomes after ST-segment elevation MI.
Electrocardiography , Fatty Acids, Nonesterified/blood , Heparin/administration & dosage , Myocardial Infarction/mortality , Thrombolytic Therapy/methods , Tissue Plasminogen Activator/administration & dosage , Biomarkers/blood , Cause of Death/trends , Drug Therapy, Combination , Female , Fibrinolytic Agents/administration & dosage , Follow-Up Studies , Humans , Injections, Intravenous , Male , Middle Aged , Myocardial Infarction/blood , Myocardial Infarction/drug therapy , Prognosis , Risk Factors , Survival Rate/trends , Time Factors , United States/epidemiology
BACKGROUND: Hyperbilirubinemia in jaundiced neonates is routinely assessed by use of total serum bilirubin. However, the unbound or free form (B(f)), not total bilirubin, crosses the blood-brain barrier and can be neurotoxic. Although the peroxidase-mediated oxidation of bilirubin can be used to measure plasma concentrations of B(f), this measurement is relatively complex and the assay is not routinely used. We describe a fluorescence sensor for quantifying B(f) in plasma. METHODS: Our method uses a mutated fatty acid binding protein labeled with the fluorescent molecule acrylodan (BL22P1B11), whose fluorescence is quenched upon binding bilirubin. Another configuration (BL22P1B11-Rh) was developed that uses BL22P1B11 together with the fluorophore rhodamine B, which responds by a change in the ratio of its fluorescence. RESULTS: The "B(f) probes" were calibrated with aqueous solutions of bilirubin and yielded similar bilirubin dissociation constants [K(d) = 16 (1.5) nmol/L]. We used the probes to determine B(f) concentrations in equilibrium with human serum albumin (HSA) and in human plasma samples supplemented with bilirubin. We obtained equivalent B(f) values in both systems, and the B(f) probe results were in agreement with the peroxidase assay. B(f) measurements revealed that bilirubin-HSA binding was well described by 2 sites with K(d) values of 15.4 (1) nmol/L and 748 (14) nmol/L. We measured B(f) concentrations in the range expected in jaundiced neonates with a mean CV of approximately 3%. CONCLUSIONS: The BL22P1B11-Rh probe provides accurate plasma sample B(f) concentrations with a single measurement, in 1 min with either a handheld B(f) meter or a laboratory fluorometer.
Bilirubin/blood , Biosensing Techniques , Fatty Acid-Binding Proteins , 2-Naphthylamine/analogs & derivatives , Adult , Animals , Calibration , Fatty Acid-Binding Proteins/genetics , Fluorescent Dyes , Humans , Infant, Newborn , Mutation , Protein Binding , Rats , Rhodamines , Serum Albumin/metabolism
We report the first measurements for profiling mixtures of unbound free fatty acids. Measurements utilized fluorescent probes with distinctly different response profiles for different free fatty acids (FFA). These probes were constructed by labeling site-specific mutants of the rat intestinal fatty acid binding protein (rI-FABP) with acrylodan. The probes were produced and screened by high-throughput methods, and from more than 30 000 such probes we selected six that together have sufficient specificity and sensitivity for resolving the profile of unbound FFA (FFAu) in mixtures of different FFAu. We developed analytical methods to determine the FFAu profile from the fluorescence (ratio) response of the different probes and used these methods to determine FFAu profiles for mixtures of arachidonate, linoleate, oleate, palmitate, and stearate in equilibrium with bovine serum albumin (BSA). Measurements were performed using mixtures with a range of total FFAu concentrations, including 0.9 nM, which is similar to normal plasma levels. We also measured single FFA binding isotherms for BSA and found that binding was described well by six to seven sites with the same binding constants (Kd). The Kd values for the FFA (4-38 nM) were inversely related to the aqueous solubility of the FFA. We constructed a model with these parameters to predict the FFAu profile in equilibrium with BSA and found excellent agreement between the profiles measured using the FFA probes and those calculated with this model. These results should lead to a better understanding of albumin's role in buffering FFAu and to profiling FFAu in intra- and extracellular biological fluids.
Albumins/chemistry , Albumins/metabolism , Fatty Acids/chemistry , Fatty Acids/metabolism , Fluorescent Dyes/chemistry , Animals , Cattle , Protein Binding
